Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
lab05_en:inverting_op-amp_basics_amplification [2026/05/05 10:17] – [Analysis of inverting input currents] mexleadminlab05_en:inverting_op-amp_basics_amplification [2026/05/07 12:45] (current) – mexleadmin
Line 13: Line 13:
 \\ \\
 \\ \\
-Calculate the necessary value for $R_{\rm 2}$, so that the output $U_{\rm OUT}$ is +1.5 V.+Calculate the necessary value for $R_{\rm 2}$, so that the output $U_{\rm OUT}$ is +1.5 V.\\
 Use the supply voltage of the operational amplifier for $U_{\rm IN}$. Use the supply voltage of the operational amplifier for $U_{\rm IN}$.
 \\ \\
Line 41: Line 41:
 \\ \\
 == Analysis of inverting input currents == == Analysis of inverting input currents ==
-\\ 
 \\ \\
 {{drawio>lab05:Fig-30_inverting_op-amp_inv_input.svg}} {{drawio>lab05:Fig-30_inverting_op-amp_inv_input.svg}}
Line 48: Line 47:
 \\ \\
 \\ \\
-$U_{\rm DD}{\rm~=10~V},~U_{\rm SS}{\rm~=-10~V},~R_{\rm 1}{\rm~=100~k\Omega}$\\ \\+$U_{\rm DD}{\rm~=10~V},~U_{\rm SS}{\rm~=-10~V},~R_{\rm 1}{\rm~=100~k\Omega}$\\
 Use the values from <imgref Fig-20_inverting_op-amp> for $U_{\rm IN},~U_{\rm OUT},~R_{\rm 2}$. Use the values from <imgref Fig-20_inverting_op-amp> for $U_{\rm IN},~U_{\rm OUT},~R_{\rm 2}$.
 \\ \\
Line 61: Line 60:
 \\ \\
 \\ \\
-$U_{\rm 2}{\rm~=}$\\+$U_{\rm 2}{\rm~=}$
 \\ \\
 \\ \\
 \\ \\
 \\ \\
 +$I_{\rm 1}{\rm~=}$
 \\ \\
 \\ \\
 \\ \\
 \\ \\
 +$I_{\rm 2}{\rm~=}$
 \\ \\
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-\\ 
-$I_{\rm 1}{\rm~=}$ 
-\\ 
-\\ 
-\\ 
-$I_{\rm 2}{\rm~=}$ 
 \\ \\
 \\ \\
 \\ \\
 $I_{\rm N12}{\rm~=}$ $I_{\rm N12}{\rm~=}$
-\\ 
-\\ 
-\\ 
 == Analysis of inverting input voltages == == Analysis of inverting input voltages ==
-\\ 
 \\ \\
 \\ \\
Line 138: Line 85:
 \\ \\
 \\ \\
-$U_{\rm DD}{\rm~=10~V},~U_{\rm SS}{\rm~=-10~V},~R_{\rm 1}{\rm~=10~k\Omega}$\\ \\+$U_{\rm DD}{\rm~=10~V},~U_{\rm SS}{\rm~=-10~V},~R_{\rm 1}{\rm~=100~k\Omega}$\\
 Use the values from <imgref Fig-20_inverting_op-amp> for $U_{\rm IN},~U_{\rm OUT},~R_{\rm 2}$. Use the values from <imgref Fig-20_inverting_op-amp> for $U_{\rm IN},~U_{\rm OUT},~R_{\rm 2}$.
 \\ \\
Line 145: Line 92:
 Complete the reference arrows in the scematic of the circuit.\\ Complete the reference arrows in the scematic of the circuit.\\
 Take the values for $U_{\rm 1},~U_{\rm 2},~U_{\rm OUT}$ from <imgref Fig-30_inverting_op-amp_inv_input>.\\ Take the values for $U_{\rm 1},~U_{\rm 2},~U_{\rm OUT}$ from <imgref Fig-30_inverting_op-amp_inv_input>.\\
-Calculate the voltage $U_{12}$ using Kirchhoff's Voltage Law (KVL) within the circuit loop.\\+Calculate the voltage $U_{12}$ using Kirchhoff's Voltage Law (KVL) within one of the possible circuit loops. Mark the chosen loop in the circuit.\\
 Verify your calculated result by measuring $U_{12}$. Verify your calculated result by measuring $U_{12}$.
 \\ \\
Line 155: Line 102:
 \\ \\
 $U_{\rm 2}{\rm~=}$ $U_{\rm 2}{\rm~=}$
 +\\
 +\\
 +\\
 +$U_{\rm IN}{\rm~=}$
 \\ \\
 \\ \\
Line 168: Line 119:
 Measured $U_{\rm 12}{\rm~=}$ Measured $U_{\rm 12}{\rm~=}$
 \\ \\
-\\ \\+\\  
 +\\
 Analyse the physical significance of the potential at $N_{12}$ relative to GND (defined as $U_{12}$) in the context of the operational amplifier's input configuration. What do you observe?\\ Analyse the physical significance of the potential at $N_{12}$ relative to GND (defined as $U_{12}$) in the context of the operational amplifier's input configuration. What do you observe?\\
 \\ \\ \\ \\